Quixk question I disconnect the wallbox from my Seeburg ay160 and now I cant make any selections on the jukebox anymore. It will except the coin show a credit and once you make selection the number and letter buttons stay down and the mech doesn't move. I never had a problem before I connected the w...

Yes the stepper has been serviced and recapped. The wallbox seems to be ok once power once sent to it. I noticed that when you put a dime in the slot it will let you make a selection but the selection light only comes on after a fee coins. Not sure if just the sockets are dirty since the box had bee...

Thanks I was able to get the cover off by prying up a little on the top and on bottom without damaging any of the casting. I took the lock assembly out and the linkage of the wallbox turned no problem. So I believe the lock has been changed and never crossed the old number off or the lock internals ...

Yes I am new to woms. It could be a possibility that it wasn't x'ed out. I've tried laying it on it's back but no luck there. Is it possible to get a copy of a master key that would open all locks?

Have a Seeburg Wall O Matic 200 D-3WU and it has an s999 lock on it. I ordered a key and can't seem to get it to open. The key will fully insert and will only wiggle a little. I've sprayed the lock with some lubricant and no luck. Was wondering if someone had any other tips of tricks to free up the ...

I have An Ay160U what would you do next to figure out exactly where the problem resides. On the detent switch is a resistor or capacitor across the two wires. Is that something that normally fails?

I am using the correct troubleshooting guide and all it's states is to install a new 0a2 tube in pulse amp which I've done. And to install new 2050 tube which I've done. I've even tried installing another pulse amp but still no luck. As the mech scans the manual states you should see some flickering...

If I scan the mech and hit the contact on the detent switch the mech will stop and pick up a record. I have a feeling my problem could be the tormat memory unit. I've recapped the tsu and stepper and replaced all the tubes. I also resilvered the contact plungers. I've checked alignment of the tmu se...

We'll I have a problem with my juke and it scans twice and stops. So I decided to make sure everything is where it's supposed to be as far as mechanically.

I am adjusting the clutch 2 on my AY 160 and I follow the manual but when I come to the point where it says turn adjustment screw in until there is no in and out play between detent arm roller and peak of sprocket tooth. This is correct starting position. Then it says back out screw 2 turns. What do...

I'm having a hard time finding 32 guage wire. The closest I found is 22 guage and it really thin. Would this work on the contact block that rides the tmu.

Wayne, Did you note Rob's first line above ? Will it now detent at EVERY selection, if the TMU is "flipped" with a known good D cell ?? Hey Ron, It will still not detent every selection, it will skip the first six records pick up four in a row skip a couple pick up another four or five sk...

Ok before I start to do that I just want to clarify what I've been trying. I go through the troubleshooting guide for when the mech scans twice and stops. The first test is to connect one wire to c and while mech is scanning insert other end of wire into pulse amplifier input. It should trip, mine d...

Ok so I recently recapped the tsu5 and reinstalled all the tubes and put back inside the seeburg. I also resilver end the contact plungers that ride the tormat. After all that it still scans twice and doesn't pick up a record. Where should I start to check next? What is the best way to check the tor...

Ron I was thinking of replacing the RCA plug that plugs into the pulse amplifier. Right now on mine the green wire goes to the long post and the red and bare wire are twisted together and soldered to the shell. Is this correct before I solder on a new plug?