Jim, Sorry about the late reply but i just happened to look in the wanted section. No i have not sold them. I had a buyer for the ds160 as is but i have not heard back. And i thought about restoring the ds160. But i may just part it out i need to make room. I also have two seeburg ss160. That i need...

George,
Thank you for the information i will try it. And hopefully it will get this jukebox going. I will let you and Ron know what happens. Thanks again.
Wayne

Ron,
Thanks i will remove it. And hold on to it. Thanks Again
Wayne

Ron, Thank you i will start there. Also i did find a cable tha comes from the left side of the magazine as you are facing the front of the jukebox one side is connected to the bottom left of magazine to a circuit board type connector that just plugs in and the other side of cable has two similiar co...

Ron, The gripper arm was over the turntable like it had placed a record on the turntable that's how he brought it to me. And i dont know if i made matters worse because i figured that the gripper arm needed to be resting over the magazine so i found the motor and i was able to turn it by hand at the...

Ron, I can help you with your car make sure you park at the top of the hill. Haha no I'm glad see such humor. Let me break it down, the service switch will not scan and i did take it and move the switch to the operate area. Now i make a selection and the inner arm begins to rotate and finds the sele...

Hello everyone, Alright looking for some help. I do have the manual, and yes I'm not up on all the correct lingo but i am matching it up to the manual. I am trying to help out a friend that would like to get this jukebox working for him. Never touched a rockola, just familiar with seeburg and Wurlit...

Hello Darrell, I might have a set of very good condition to excellent on the DS160 ears. I have a DS160 with awesome ears on it have not tested them yet but they are in great condition with only one small crack in the back on the black housing part of one speaker. Both speakers were opened up and ch...

Thank you Gentlemen, I appreciate all the input. I on the other hand am not familiar with the caps. I actually have a TV repair guy that does all my soldering and replacing caps and he mentioned that you had to be aware of the +/- on these so I am guessing he knows what hes doing because he informed...

Thanks Again Ron,
That cleared it up and now I know they said it was okay but i wanted to make sure for this application. Thanks Again!
Wayne

Hello Ron and Everyone Else, I appreciate the information. But also for future references, can radio capacitors be used of the same value(mfd/V). I was told only difference was the wires all came out of one end instead of opposite ends. And just for reference in case if I need a capacitor to get rig...

Hi everyone, I completed my Wurlitzer 2810. And now i am in the middle of Seebug DS160, and here is the prob lem i am replacing all of the paper lytic capacitors and i saw some kits that were specific for the DS160 and it stated that the most common ones to go bad were in the kit but it did not say ...

Ron, Thank you again i did not see a reference in the manual might have missed it and going crazy trying to trouble shoot it. I am still tring to get numbers 6-0 working otherwise everything else and the bulb is working perfect. Also if anyone knows how to replace the light diffuzer on the 2810 plea...

Hello Ron, I am sorry, yes it was a #12 Bulb okay I see where it goes but is it supposed to be lit all the time or just when speed changes ie 45/33 1/3 . Because mine is not lit and i was going to check that pancake capacitor that its conected to or the coil that the two prongs come off. But thank y...

Thanks Ron-NYC I will check the driver and also recheck plugs someone else told me to recheck the plugs also because they had one where center of plugs had broken and the pin/ plug still fit any way without that center piece. Also Ron-NYC I will look to joining that Wurlitzer group you suggested. An...